NOTE: Support for multiple transmitters requires a Managed network switch with VLAN/IGMP support. Standard LAN switches can only support 1 transmitter.
Not an HDMI Balun, but an HD over IP system. This means you can create your own A/V Ethernet network and all of the recievers will find the transmitter automatically. It may even be used over smaller existing house networks and low cost LAN switches and routers.
Any HD source can simultaneously be diplayed on any number of display devices (if multiple displays are permitted by the HD source) using VLAN isolation on a Managed Ethernet switch. Using an HTTP GUI like MediaSwitcher(tm) a PC (wired or wireless) can control what signal is being watched at each location. Sophisticated Home Theater installations can use a programmable console to control the system using RS232 commands. The Managed switch must support IGMP and permit duplicate IP addresses across the VLAN domains. You must use a third party home automation solution to provide distributed remote control functionality.
Managed Ethernet Switches we have tested and found to be compatible with the Just Add Power HD over IP solution include the following:
Cisco SG300Cisco Catalyst 2960Cisco Catalyst 2960 GigabitDell PowerConnect 3500 Series (3524, 3548)Dell PowerConnect 5400 Series (5424, 5448)Dell PowerConnect 6200 Series (6224, 6248)DLink DES-3226LNetgear 7000 Series V2 (GSM7224, GSM7228PS, GSM7248, GSM7252PS)Pakedge SW24-GBM, S24P
2G Systems (requires Gigabit for best results):
Cisco SG300 GigabitCisco Catalyst 2960 GigabitDell PowerConnect 5400 Series (5424, 5448)Dell PowerConnect 6200 Series (6224, 6248)Netgear 7000 Series V2 (GSM7224, GSM7228PS, GSM7248, GSM7252PS)Pakedge SW24-GBM, S24P
Home automation drivers have been written for many of these switches. These drivers are specific to the switch make/model and must often be customized to deliver the desired results. Please call us with the details on the home automation platform you intend to use to see if a driver has already been written to support a certain switch. We have drivers available for several platforms, including AMX, Crestron, Control4, Pronto, RTI, Savant, URC, and Vantage, with more being developed all the time.
Projector Connector™ HD/IP Receiver Specifcations (VBS-HDIP-108A)
1 UTP/STP 100Mbps Ethernet Port1 HD Out (19 pin Type A female)Protocol: IP, UDP, TCP, ICMP, and IGMP1 Integrated IR Eye in front plus 1 3.5mm IR Eye Port in back (limited support)Size: 5” W x 4.5” D x 1” H; 1.1 pounds100-240V, 50/60 Hz, DC5V 1.5A positive tip power supplyPlug-and-Play installationSupports DVI with HDMI-to-DVI adapter cableScaler automatically adjusts for each displayVideo Bandwidth: 2.25GbpsLAN Bandwidth: 50Mbps ~ 60Mbps for 1080p Input TMDS Signal: 1.2 volts (peak-to-peak)Input DDC Signal: 5 volts (peak-to-peak)Resolutions - supports practically any input resolution and frequency from 16 x 16 to 2048 x 2048 pixel image including the following popular settings (NOTE the integrated scaler will automatically adjust the HD output to match the preferred resolution setting reported by the EDID of the attached monitor):640x480 @ 85fps 800x600 @ 85fps1024x768 @ 75fps 1280x1024 @ 30fps1600x1200 @ 30fps 720x480 @ 60fps720x576 @ 50fps 1280x720 @ 30fps1920x1080 @ 24fps 1920x1080 @ 60fpsNOTICE: HD over IP and HD/IP are global trademarks or registered trademarks of Just Add Power Cardware Co., Inc. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.